Forum Replies Created
-
Posts
-
Re: Decent American Style Fridge – Help please!
Beko American Style Fridge Freezer GNEV221APB is a decent enough one at £569
Re: ignition fault
They should be, but they may need to confirm that this is the actual fault first. You can ask them, say what you think & the advice you’ve gotten, see what they say.
Re: Amica AWCT10L Washing Machine
Test meter time i’m afraid, could be a fault anywhere in it, as stated heater & motor could be problem, but if theres a short to earth somewhere you can find it by testing the components individualy, maybe its as simple as a faulty plug.
Re: Washing machine filter always full of water please help
There should be water in the filter, but the drum should be empty.
Suspect there is a blockage somewhere.Re: JLDW1201 drain hose replacement
This one is the hose you require,
https://shop.ukwhitegoods.co.uk/catalog … 1526492010
can’t guarantee the one in your post is exact fit..Re: AEG Electrolux E9 cooker fault D98000VF 948522155 Cerami
Would get them to double check the cable connections are correct, one of the plugs can go on incorrectly from memory, for instance there may be 9 connections on the socket of P.C.B but the plug is 8 way, if its not on the socket correctly the way the original one was it will give error code.
Small data cables between the P.C.Bs on these are the most tempermental & give errors, sometimes making you think its more serious a problem. But if board was burn’t out then thats in need of replacement.Re: Zanussi ZWF 1021
On a ZWF1021.
Its a 5 minute procedure through the door, never took the front off one.
But in answer to your question, yes it comes off.If its however an older type ZWF1021W, its the older type of zanny, that outer casing splits at the sides.
Re: lamona/beko hja8631 dishwasher
Hold in the reset button for at least 5 seconds, see if it clears itself.
Possible that you have or because of poor installation that 2 buttons are pressed in when door is closed. I’ve had this kind of problem that a mounting screw on the brackets holding appliance in place are not in far enough & when door is closed buttons are pushed in by said screws.
Something to check, when you check this will you let us know what the “buttons flashing” are.
Do you mean the program selection button for & start buttons?
May need a display card p.c.b replaced.Re: JLDW1201 drain hose replacement
You are best to get the proper hose for the appliance & clips required. Best not to bodge it, as you could flood the house very easilly.
Re: ZANUSSI DISHWASHER ZDF2020 FAULT
Everything tested o.k??
Did the heater come on?
Did it drain o/k?
Is there a leak to base?Known faults on this machine is not heating, but i’m presuming as you have stated that “Everything testing o.k” that this has been checked. Longer times can be down to poor water pressure(kinked pipe for instance), poor draining because of blockage in pipework or filters, poor pump performance, failing pump etc.
Re: Zanussi washing machine model zwg1120m E62 error code
It needs a PCB replaced, the motor control triac has gone on the P.C.B, done dozens of them, P.C.B required, is E62 on these not normally a motor or tacho problem.
Re: Beko FSA 706 too warm
Quick inspection of the door switch contact on fridge door, have found some of these to get damaged & not knock off switch for internal light in fridge causing warm fridge.
Re: Belling XOU270SS blowing trip
We come across this regularly in the trade.
Most likely the elements are low, meaning that there is a slight short to earth. Normally you will find this on ones that have been not stored in a warm dry environment prior to fitting in kitchen.
Something you can do yourself is turn on the oven controls without switching on appliance, disconnect the earth lead going to the appliance & run on test for say 1/2 hour to an hour.
WARNING 💡
While its on test its extremely important that no one touch it. After period, switch off cooker switch, re-attach earth connection & try now.
If that hour or so doesn’t dry out elements & trip still goes off, i’d check the resistance of elements with a megger, if they are low to earth you may need to fit new elements.
