spimps

Forum Replies Created

Viewing 15 posts - 301 through 315 (of 1,200 total)
  • Author
    Posts
  • in reply to: Hotpoint 8764 Freezer #361428
    spimps
    Participant

    Re: Hotpoint 8764 Freezer

    Sometimes easier if you take the door off via the bottom hinge and lay it on a table to change seal,easy,peasey lemon squeezy.
    Seriously it is an easy change,when first fitted the seal often looks a poor fit but wait a few hours and it will shap[e up to the cabine.A bit of warmth from a hair dryer will help overcome any creases from being packaged.
    BG

    in reply to: Whirpool american fridge freezer given up. #361238
    spimps
    Participant

    Re: Whirpool american fridge freezer given up.

    It sounds like the compressor has failed.
    If the condenser/compressor fan runs so should the compressor.
    You could after unpluging test for continuity through the three pin compressor terminals in a triangle,after removing the relay/ptc etc,three values should be read,resistance will be different between all three terminals but two should add up to the value of the other reading.
    If one is open circuit it would be a new compressor,specialist job.
    BG

    in reply to: CTD00P #360806
    spimps
    Participant

    Re: CTD00P

    Thanks for your help.
    BG

    in reply to: Freezer keeps on running EU2246c #360721
    spimps
    Participant

    Re: Freezer keeps on running EU2246c

    What temp is it acheiving,if the system is ok and it’s running constantly then would expect the temp to be-25 or lower.
    Check the cabinet temp with a decent thermometer.
    Compressor wear could well be the problem @10 years old.

    in reply to: Hotpoint EW84 Cooker Grill #360807
    spimps
    Participant

    Re: Hotpoint EW84 Cooker Grill

    Energy regulator,MDA6204035 is the part number I think but double check with supplier.

    in reply to: hotpoint mistral fridge freezer #360396
    spimps
    Participant

    Re: hotpoint mistral fridge freezer

    Could be as low as -14c when starting from cold before the fan starts.
    remember switch off first.
    If you switch off at plug and then hold down the save button when switching on it wil run a short test 10 seconds evap heater then 10 secoconds gutter heater then 10 seconds ff led display then 10 seconds fan.
    Could be case of checking all connectors on the board too.
    No mention of P1 in the manual.
    Best of luck.

    in reply to: hotpoint mistral fridge freezer #360394
    spimps
    Participant

    Re: hotpoint mistral fridge freezer

    Is the fan running normally,dont forget that when you switch on after replacing parts the fan doesnt start straight away,it starts when the thermistor senses the evaporator temp @ -12c ish,which can take several minutes to acheive.
    Check the duct which returns air from the fridge into the freezer is not blocked,it sits at the bottom right hand corner of the freezer just behind the evaporator.
    Is the flap opening in the top left hand corner of the fridge which allows air from the freezer into the fridge ?

    spimps
    Participant

    Re: Bosch fridge dripping water from under freezer compartme

    Not a good effort from me that one r600a,it is worth disconnecting the wooden door from the fridge door usually a couple of screws on each plastic strip, you can then ensure it is closed and sealing correctly.
    BG

    in reply to: Another joke. #137549
    spimps
    Participant

    Re: Another joke.

    Apparently there is a larger than normal settlement of Japanese people in Harrow,the reason is when they approach the airport taxis the first word they say is “Harro”.

    spimps
    Participant

    Re: Bosch fridge dripping water from under freezer compartme

    Fridge with a small freezer inside,condensation is likey due to a refrierant loss,you would need engineer to check,trace and find leak before re gassing.

    in reply to: Candy cp2610/9 part #359899
    spimps
    Participant

    Re: Candy cp2610/9 part

    Making stuff damp,not cat pee is it ? 😯
    If there is damp around any surfaces ie the back or underneath,signs of condensation on the sides or top of the fridge freezer then its time for a new one,if it is working correctly it certainly isn’t the reason your cupboard is damp.
    You have pulled of the relay/start device and it will also have he mains terminals on there.Not permitted to give re-wiring instructions so suggest you get a local engineer in to carry out the repair safely.

    in reply to: Whirlpool fridge Freezer #359507
    spimps
    Participant

    Re: Whirlpool fridge Freezer

    Hereis some info.

    in reply to: Siemens Fridge Model No KU15RAGB #359365
    spimps
    Participant

    Re: Siemens Fridge Model No KU15RAGB

    hould be able to remove plinth then hinge bracket which will have a spigot on that enters the door as the pivot,may just need a spacing washer adding.

    in reply to: Anthropologists,what young bird? #359158
    spimps
    Participant

    Re: Anthropologists,what young bird?

    Think it was a young jackdaw,why did I title it Anthropology? :rolls:
    11 plus failures will out!

    in reply to: Whirlpool Toploader 3RLSQ8033SW0 overfilling #359038
    spimps
    Participant

    Re: Whirlpool Toploader 3RLSQ8033SW0 overfilling

    Useing a different or new tube actuate the pressure by blowing in the tube,then kink it at the end and fasten it to see if the presure switch does hold and not re set,chafing of the tube is also a possible cause

Viewing 15 posts - 301 through 315 (of 1,200 total)