Washman

Forum Replies Created

Viewing 15 posts - 271 through 285 (of 894 total)
1 2 3 … 18 19 20 … 58 59 60
  • Author
    Posts
  • November 19, 2009 at 7:25 pm in reply to: Burnt out microwave #304221
    Washman
    Participant

    Re: Burnt out microwave

    Hi

    Yes do not use until checked out by microwave engineer.

    Washman

    November 19, 2009 at 12:50 pm in reply to: Burnt out microwave #304218
    Washman
    Participant

    Re: Burnt out microwave

    Hi

    Usually caused by appliance not being cleaned properly , and crud building up around wave guide.

    Washman

    November 18, 2009 at 3:57 pm in reply to: TDS cd rom #304073
    Washman
    Participant

    Re: TDS cd rom

    Hi

    TDS 2009 V1 Loaded onto my Vista laptop with no problems. Copied whole disk to hard drive and it works OK.

    Mike

    November 12, 2009 at 4:36 pm in reply to: SERVIS M6100S #303505
    Washman
    Participant

    Re: SERVIS M6100S

    Hi

    Its a Vestel made machine for Servis.
    Serial no is different format to Italian made Servis machines.

    Mike

    November 9, 2009 at 6:41 pm in reply to: Leisure Rangemaster 110 Timer #303006
    Washman
    Participant

    Re: Leisure Rangemaster 110 Timer

    Hi

    Looked there ,cannot find any labels.

    Mike

    November 8, 2009 at 7:54 pm in reply to: HENEKEN HALF HEIGHT BENCH TOP FRIDGE PROBLEM #302917
    Washman
    Participant

    Re: HENEKEN HALF HEIGHT BENCH TOP FRIDGE PROBLEM

    Hi

    If cooling plate is icing over then defrosting when cabinet reaches 4 degrees and thermostat shuts the compressor off,it is working correctly.
    The tray on top of compressor is there to evaporate the defrost water from the cooling plate.
    Try a new fan to cool compressor , they do run to hot to touch at normal operating temps.

    Mike

    November 4, 2009 at 6:43 pm in reply to: Hotpoint washing, and washing, and washing…. #302613
    Washman
    Participant

    Re: Hotpoint washing, and washing, and washing….

    Hi

    Has the module been programmed for this machine.

    Mike

    October 27, 2009 at 12:17 pm in reply to: Bosch D/W #300538
    Washman
    Participant

    Re: Bosch D/W

    Hi

    Check corrigated hose from fill matrix to sump for blockage.

    Mike

    October 26, 2009 at 2:52 pm in reply to: Homark oven help #300340
    Washman
    Participant

    Re: Homark oven help

    Hi

    Model number would be a great help.

    Washman

    October 23, 2009 at 6:45 pm in reply to: Belling IDW 603 E1 Low water pressure error #300257
    Washman
    Participant

    Re: Belling IDW 603 E1 Low water pressure error

    Hi

    The orange stuff is the water softener,so do not try to remove.

    Washman

    October 15, 2009 at 3:21 pm in reply to: Diplomat ADP3300 Oven #299610
    Washman
    Participant

    Re: Diplomat ADP3300 Oven

    Hi

    Have you set the timer to manual, if its set to auto the oven will not work.

    Mike

    October 9, 2009 at 12:46 pm in reply to: Hoover Maxi 6 TC50 Tumble dryer on/off switch problem #299077
    Washman
    Participant

    Re: Hoover Maxi 6 TC50 Tumble dryer on/off switch problem

    Hi

    Relay PCB needs replacing .

    Washman

    Power off and plug out when working on appliance.

    October 9, 2009 at 12:45 pm in reply to: White Knight low heat #299085
    Washman
    Participant

    Re: White Knight low heat

    Hi

    Have you checked out the heater,as it is a double one.
    ie:- one on for low heat both on for high heat.

    Washman

    October 6, 2009 at 7:33 am in reply to: Siemens lower sprayer not working #298750
    Washman
    Participant

    Re: Siemens lower sprayer not working

    Hi

    Does that machine have an option button for top rack or half load .

    Mike

    October 3, 2009 at 2:55 pm in reply to: WHIRPOOL ADG934 Stuck in empty #298559
    Washman
    Participant

    Re: WHIRPOOL ADG934 Stuck in empty

    Hi

    The base has flooded and safety float activated to stop machine from flooding. You need to investigate for leaks. Also count the number of flashes this is the fault code.

    Washman

  • Author
    Posts
Viewing 15 posts - 271 through 285 (of 894 total)
1 2 3 … 18 19 20 … 58 59 60