washtronics

Forum Replies Created

Viewing 15 posts - 76 through 90 (of 288 total)
  • Author
    Posts
  • in reply to: BUSH APPLIANCES #367547
    washtronics
    Participant

    Re: BUSH APPLIANCES

    i went to a bush washing machine and it was the same as an amica awp510l and a statesman mxw10252

    in reply to: DeLonghi Range Cooker #367043
    washtronics
    Participant

    Re: DeLonghi Range Cooker

    done quite a few on delonghi and elba (same cookers) easy job. Check door hinges, they wear quickly as a very heavy door. Genuine parts only available, no pattern

    in reply to: miele w404 door seal #367095
    washtronics
    Participant

    Re: miele w404 door seal

    couldnt beleive cost of genuine miele part for door seal, over £60. A heater was around £100

    in reply to: Smeg oven SUK61MPXS #365394
    washtronics
    Participant

    Re: Smeg oven SUK61MPXS

    i agree, i have had a neff oven with electronics that customer said not getting to temp, not even worth looking at as cost ofelectronics and sensors make it impossible to give a sensible quote. Ovens with switches, variable thermostats, you know where you are with them as a stat is cheap as chips and every engineer stocks them

    in reply to: never been so quiet #366985
    washtronics
    Participant

    Re: never been so quiet

    was busy, now gone quiet

    in reply to: BOSCH SGS46E22GB/01 Check water light on after 1 minute. #366960
    washtronics
    Participant

    Re: BOSCH SGS46E22GB/01 Check water light on after 1 minute.

    could be jug impellor

    in reply to: Hygena Cooker Extractor Hood – App 2440 #366941
    washtronics
    Participant

    Re: Hygena Cooker Extractor Hood – App 2440

    look for dry joints on the switch pins that connect to circuit board, just resoldering usually cures it

    in reply to: Cannon Gas cooker 10675G igniter constantly firing #366967
    washtronics
    Participant

    Re: Cannon Gas cooker 10675G igniter constantly firing

    check the electrode cable for shorting out on a metal part somewhere, if not then change spark generator

    in reply to: help 3lights flashing ariston a1636 fault code #366649
    washtronics
    Participant

    Re: help 3lights flashing ariston a1636 fault code

    no difference, as long as its the same dimensions

    in reply to: Miele T4262C #366673
    washtronics
    Participant

    Re: Miele T4262C

    could just be a thermostat,I have been able to reset these quite easily, shouldnt be too expensive to get repaired. These are quality appliances so keep hold of it

    in reply to: help 3lights flashing ariston a1636 fault code #366640
    washtronics
    Participant

    Re: help 3lights flashing ariston a1636 fault code

    yes, replacing the heating element should cure the fault. Not the pcb (module)

    in reply to: help 3lights flashing ariston a1636 fault code #366638
    washtronics
    Participant

    Re: help 3lights flashing ariston a1636 fault code

    if its open circuit then you must change it.It is very difficult to get a used heater back in again. F07 is heater not the module

    in reply to: Amica awct12l module #366494
    washtronics
    Participant

    Re: Amica awct12l module

    8037970 is the module part number

    in reply to: Ariston S1200A #366527
    washtronics
    Participant

    Re: Ariston S1200A

    this machine has a 3 leg spider , very easy job. It is 6205 and 6206 bearings and oil seal C00082696

    in reply to: Neff S54T09X1GB/06 just pumps #366138
    washtronics
    Participant

    Re: Neff S54T09X1GB/06 just pumps

    could be gunged up on the water metering device, i had one doing the same thing, and the microswitch would not reset because it was gunged up with mould and scale

Viewing 15 posts - 76 through 90 (of 288 total)