Forum Replies Created
-
Posts
-
Re: Off topic cricket question.
If you enjoy Billy Bermingmans work A really good read (very Funny Spoof on cricket )is The Warrick Todd Series By Tom Gleisner
Re: Removing agitator from a Fisher and Paykel GW501?
Remove Agitator cap (Fabric Softener Cap) this just pulls Out
Put Hand down centre of Agitator And Unscrew wing nut
Agi just pulls offRe: Fisher & Paykel GW501 Smart Drive code 37?
Fault Code 37 Pump error
Either something jammed in pump or Pump itself Faulty
Pump Located under Washer
It sits under Bowl
Give Fan of Pump A Bit of a Tweek and it may free up Whatever is Stuck in there
If not you may have To remove pump
It Twist locks off & On the Mounting bracket
Check pump for signs of Water leakage
Pumps do have a Overload if they get to hot will shut Down
Power OFFRe: Fisher & Paykel 918TD keeps pumping
This unit has a Flood Switch under base
When Activated generally comes up With F1 fault
If there was Water in the base this should activate Flood Switch (Micro switch)At Start of Wash cycle Drain pump Will come On Always For 15 Sec
Maybe just check base again to See If Micro switch hasnt Jammed upRe: LG Dishwasher Beeping like crazy LD- 14at2
No error Codes ?
Can you post Serial number pleaseWould Say its PCB
Re: Fisher and Paykel Smart Drive MW059AU
Fault code 43
Common OOB (Out Of Balance)Micro switch fault
Washer thinks its OOB
CHeck micro switch terminals corrode
Switch located in console under Main PCB (Motor Controller) RHS
Check that bowl is sitting central ,if hanging to side Check Bias Spring Front LHS (This Little Spring keeps bowl central )Re: GW612 with error after relocation
Is The Lid Lock Light flashing??
Note on Spline
When washer fills with water the bowl LOCKS onto Spline
When Washer pumps out the bowl then lifts to up off the spline to allow free rotation on Spin
When bowl is empty bowl should move vertical freely
Position of bowl is determined by water levelFault code 56 Reads
While carrying out bowl check ,the machine has not been able to determine a valid bowl status so flags this display codeCause of faults
Primary /Secondary As Suggested by Penguin
Tertiary / Rotor Postion Sensor (RPS)
Lastly / Can be Motor Controller (PCB)Re: Fisher and Paykel Smart Drive GW501
To check size setting use Diagnostic Mode
IE Press & hold Washtempdown & power
If Short Wash LED on Size Is not set
If Rinse LED IS On Size is Set For 5/5.5 KG (In your case)Check size Setting
Re: Fisher and Paykel Smart Drive GW501
Size Switch Error
When PCB Is Exchanged you have code in Size of Washer
Have To enter Option Mode
Power off at Console
Press & hold Start/Pause Press Power. Power OF Again to Store
To check size setting use Diagnostic Mode
IE Press & hold Washtempdown & power
If Short Wash LED on Size Is not set
If Rinse LED IS On Size is Set For 5/5.5 KG (In your case)Re: GW701 Error code 43
Out Of balance switch fault
Check OOB microswitch (Terminals corrode) Also Check Switch housing pins that hold in OOB Switch Break (Plastic)Switch located in top console RHS under Motor Controler(PCB)
Re: F&P GW709 no power
Exactly
Check water coils for signs of cracks in casing
Check for any shorts in wiring
Particularly check lid switch harness as they can be pinched & short to cabinet
Check underneath for signs of water leaks
If All seems Ok Then it can be a matter of controller itselfIf in doubt i make a point of replacing Hot Valve Assy ($29AUD) When replacing Motor Controller on this series(09)
