[electrofix]

Re: AWM5145 / 5 door boot

yes as far as i know searched qualtex fitted a gen one 12 month ago think have fitted another one since but cant trace record

Dave

used part no 481246068617

[electrofix]

Re: one for mike LMTGOWI / jim IADOM – miele w800 6 switch p

bridging out blown tracks will only work if you know why they have blown

as with most miele units the wiring sheets are inside
trace blown track to see what it feeds its better than a big bang when you turn back on

Dave

[electrofix]

Re: Six Lux Washing Machine Drums Jammed – Not Bearings…

before you jump in look for damage to outer drum got one out last year only to find it had scored around the drum front leaving holes managed to silicone up but left saying no guarentee it wont leak

Dave

[electrofix]

Re: Diplomat/Whirlpool dw motor

if the askol motor you have has a seperate heater you fit the older type motor

pt number
481236158434

this is a very different motor much more reliable all you will need to fit are 2 self tap screws

very easy fit only problem i have is those aweful hose clips that have to crimped somtimes getting them to seal can be a challenge and you dont get new ones

Dave

[electrofix]

Re: Zanussi w/m FJS1397W poor spin

some machines wont spin unless there is a losd in

talk to tony EMW if it is a unit they repair they will test it first to see if you are correct. saves spending lots of money to find your wrong

Dave

[electrofix]

Re: Beko DRCS68

need an email address to send info

Dave

[electrofix]

Re: Zanussi Module wanted

within reason and electrical specs a relay is a relay

there must be something else to go in

have fitted relays off boards before today when correct one is not available

search both RS and Farnell one will have something to go in even if you can redrill pcd for the odd hole that does not match

Dave

[electrofix]

Re: Sharp R7A50 Microwave tt motor &oven light on all time

check printed circuit board for damage and check for earth faults

Dave

[electrofix]

Re: Miele W918

most miele’s are not too bad

if its got 3 10mm bolts round door front panel hinges out (hinge on rhs)

if it got one at 6 o clock then whole fron panel comes off

once you have access its ok

Dave

[electrofix]

Re: Critical part????

my guess was it would allow air trapped under the filter to get out easier

thats all i can think of but zann must have had a reason

Dave

[electrofix]

Re: Fan oven thermostat

do you have a model number for the cooker 600 series i think

had a similar prob recently needed a fan oven stat for belling cooker turned out to be obsolete

ended up ringing the local belling agent i used to get spares from and he had one on the shelf
all agents got dumped when stoves took over might be worth a ring

martin and hicks liscard liverpool 0151 639 4849

Dave

[electrofix]

Re: zanussi pcb

sorted check your inbox

Dave

[electrofix]

Re: zanussi pcb

some lux boards can be configured for various models

you do not give the model but some need a hexidecimal code entered through the buttons. code is found on cover of old module and is a mixture of numbers plus letters a-f

if you let me have model prod ocde and email will see if i have manual

Dave

[electrofix]

Re: Bosch waa24171gb/12 Reset

have you seen this thread

http://www.ukwhitegoods.co.uk/modules.p … ic&t=61233

Dave

[electrofix]

Re: WHIRLPOOL SCW1112 WASHING MACHINE

this is a long shot but based on what you are saying

old aeg auto had similar problem

set up progamme and press start. motor in soap draw turns to direct water to correct draw. when motor stops machine fills

motor turns until a contact is made feeding back to the pcb and telling it to stop motor (probably)
sounds much the same. this motor will turn until it reaches correct point. motor will keep turning if

bad contacts within soap draw motor unit
bad connections to soap draw motor unit
faulty pcb

hope this helps

Dave

[Author]

Posts