[electrofix]

Re: Hotpoint wml52 lights flashing

? capacitor on board see simple pcb repairs above

http://www.ukwhitegoods.co.uk/modules.p … ic&t=51155

Dave

[electrofix]

Re: Replacement cut-out/stats for Hoover/Candy t/d heater el

i dont want to pour water on a good idea but what if?

since the users abuse this appliance and if the dryer catches fire can you prove the parts you fitted did not comprimise the safety of the appliance or deviated from the manufacturers spec

from my point of veiw i would not chance it they bought the dryers in the first place so its up to them and next time you can advise the best appliace to buy that can be repaired at a reasonable cost

Dave

[electrofix]

Re: AEG Lavamat 50700

when customer moves it on full or empty of water

?rinse hold

Dave

[electrofix]

Re: Zanussi w/d ZWD1627ow not starting wash cycle

sned me you email will give you some light reading

Dave

[electrofix]

Re: AEG Favorit 60870 PNC 911917606/02

have been through manual does not seem to mention light

part list mention liminous diode but cant see it on circuit diags

give me you email will send you docs

Dave

[electrofix]

Re: Hotpoint WD440 runs for 3 or 4 mins then trips error cod

check motor to earth

look at board for bad solder joint around relays

Dave

[electrofix]

Re: Smeg sc336x

if its the same as the one i did last week

the holes that mount the bottom of the glass are about 2 inches nearer the middle of the door. if you look on the door you have, if you moved the screws they would be in mid space.
answer two pieces of stainless steel strip to bridge the gap. you will need to find 2 self tap screws for the lower glass bracket but apart from that no probs

Dave

[electrofix]

Re: Zanussi ZWF1220w Will not pump out when put through a pr

take it you asked about rinse hold facility

had a few customers who changed cycles used and thought it was a fault

Dave

[electrofix]

Re: WTA / UKW SEPTEMBER 2010 MEETING

will have to come next time

same old story staff had time off so i could’t

Dave

[electrofix]

Re: Scarecrow Competition

looks like good fun would like to see the other entries

+ did you win?

Dave 😆

[electrofix]

Re: Electrolux dishwasher not heating

if you have replaced board and shorted pressure switch ( for test puposes) then can only be an ntc prob try measuring NTC from board

connections H1 and H3 accoring to manual 4850 ohm at 25 degrees

you could disconnect NTC and short out with 5k resistor and see if heater kick in

have got tech info if you want it but cnat thinks of anything else you have not checked or changed

Dave

[electrofix]

Re: wta4007 gb/04

how are you setting the dryer

are you setting an automatic programme if so you need wet clothes in it and clean the sensor in case customer has been using bounce type sheets

try it on a timed programme see if it stops then

Dave

[electrofix]

Re: Whirlpool Dryer AWZ 3303

you say cap seems ok have you replaced it to try even with a lower value

also are both motor windings ok check continuity

Dave

[electrofix]

Re: AEG D100-1M

i assume the no light on the top oven display

from the part lists both boards are the same do a swop

from the limited diagrams i have there seems to be a transformer on the board check the primary winding for open circuit may be a transformer failure and you may be able to source one

had a similar fault on another cooker ended up transformer was 12v out put so used a 12 halogen transormer i had lying around to provide power to the board which prooved board was ok then found a replacemant transformer and fixed the board saving the cutomer over £70

Dave

[electrofix]

Re: electrolux ESL63010 (D/W)

sent but its a big email because you did not state pnc

so if you dont get it will send in 2 halves

Dave

[Author]

Posts