Martin

Forum Replies Created

Viewing 15 posts - 3,181 through 3,195 (of 25,534 total)
  • Author
    Posts
  • in reply to: White Knight 85AW Front Bearing Pad #424502
    Martin
    Participant

    Re: White Knight 85AW Front Bearing Pad

    Remove the drum

    in reply to: PCB fault or something else? #424483
    Martin
    Participant

    Re: PCB fault or something else?

    Could also be a flooded base tray? Faulty heater?

    in reply to: Hoover HNL7146 Washing Machine Not Spinning #424481
    Martin
    Participant

    Re: Hoover HNL7146 Washing Machine Not Spinning

    Do you mean fast spin or tumble speed?

    in reply to: Belling 623WH #424480
    Martin
    Participant

    Re: Belling 623WH

    Read the Forum Rules no :8

    in reply to: Hoover Nextra HNWF 7167 not drying #424477
    Martin
    Participant

    Re: Hoover Nextra HNWF 7167 not drying

    Faulty dryer timer?

    in reply to: neff s72m63x1gb/44 #424454
    Martin
    Participant

    Re: neff s72m63x1gb/44

    Module programmed 00655651

    in reply to: Samsung WF0704W7W/XEUO1 #424452
    Martin
    Participant

    Re: Samsung WF0704W7W/XEUO1

    hoover1955 wrote:all the obvious ok,

    What exactly have you checked?

    in reply to: bosch wff2000gb/01 how to replace dispenser to drum hose #424442
    Martin
    Participant

    Re: bosch wff2000gb/01 how to replace dispenser to drum hose

    Very easily after you have removed the front panel. The black rubber corrugated hose held on both ends with screws clamp rings.

    in reply to: AEG Coffee Machine #424407
    Martin
    Participant

    Re: AEG Coffee Machine

    They haven’t produced a service manual just a basic wiring diagram ’tis all. 🙁

    in reply to: bosch wvd2452bgb stuck on 1 minute #424405
    Martin
    Participant

    Re: bosch wvd2452bgb stuck on 1 minute

    The 4 dashes (—-) show that the dryer time has completed (or wasn’t set to do a dry)

    The 1 minute left probably relates to pump time-out. Blockage? Knackered Pump? Blocked air chamber?

    in reply to: zanussi wks1265w #424372
    Martin
    Participant

    Re: zanussi wks1265w

    Either an earth leak on dryer heater or a fault with analogue pressure switch? I’ll put my money on the dryer element. 😉

    Place your bets……..NOW!:clown:

    in reply to: Hoover Vision HD 8142 Washing Machine #424389
    Martin
    Participant

    Re: Hoover Vision HD 8142 Washing Machine

    paun wrote:Would there be any error codes or flashing going on if the heater element wasnt working?

    Not usually. If the heater had an earth leak (insulation fault) then yes E16 would be displayed. However if the element is open circuit or the wiring to it broken, no error specific to a heating fault would show.

    Have any error codes shown at any point?

    in reply to: Hoover Vision HD 8142 Washing Machine #424387
    Martin
    Participant

    Re: Hoover Vision HD 8142 Washing Machine

    The most logical step would be to check out the heater. Guessing won’t get us very far but symptoms of not heating is a very big clue as to where the problem could lay. 😉

    in reply to: Electric ovens leaking!!!! #424184
    Martin
    Participant

    Re: Electric ovens leaking!!!!

    grooster wrote:Has anybody tried this.

    Didn’t bazza500 just say that?

    bazza500 wrote:Was advised by tech to cut the bottom of the seal off and make it a goalpost seal instead of four sided. Seems to have some the trick.

    in reply to: Bosch WAE24368GB/54 – not starting #424363
    Martin
    Participant

    Re: Bosch WAE24368GB/54 – not starting

    Hmm….might just be a duff interlock I suppose or the plug in connector to it?

Viewing 15 posts - 3,181 through 3,195 (of 25,534 total)