[Seamy]

Re: Beko drcs68w Mains Filter

Was it mains filter & or capacitor for motor that popped ?

[Seamy]

Re: BEKO WASHER – POWER BUT NOT STARTING

Caps Lock off you probably will get more help…… 😮

try interlock first, then if that doesn’t sort it, may be a P.C.B fault

[Seamy]

Re: Beko DWD5412W circ motor issue

Check loom, the cables sometimes break at bottom of door.

[Seamy]

Re: Beko WMB 61631S Power issue

P.C.B required

[Seamy]

Re: Electrolux esl6225 dishwasher repair help..

There has been an issue with the hose from sump to pressure switch on them sagging & having a pocket of gunge forming in it, so it doesn’t register full or empty.

PS it doesn’t have an inlet pump, its a solenoid valve that fills & a circulation pump that washes when filled

[Seamy]

Re: zannusi td4212 916092302-01 poor drying

Back felt bearing 1250129200 becomes dislodged on a lot of these dryers meaning heat is not guided through drum, causes heater thermostat to go open circuit very early.
Throws up E62 on them.

Air intake in then is taken from inner cabinet via element, guided through rear felt bearing into rear of drum, out through front filter down via fan & expelled via vent hose apertures at sides or rear.
Air intake at bottom/rear cabinet needs to be free of fluff, its important that appliance has plentiful airflow, not stuck in a broom cupboard for instance

[Seamy]

Re: Beko OIF21300B (single oven)

Tom wrote:I’ve got an oven with this problem, fan blade catching the element.
It is clearing the newly replaced element but only just.
The motor needs replacing too but is supplied without the circulation fan blade.
Noticed Seamy’s post with part number— 081581800.
I am finding that this comes as a belling fan motor but no circulation fan is shown.
I have belling circulation fan blades in stock but they are quite a bit smaller than the original Beko.
I ‘me wondering if you were referring to a blade a bit nearer the size of the beko but the there was an error in the part number supplied.
Thanks in advance for any replies / comments.
Tom

Part number refers to a common Belling fan motor that most Engineers would stock, it comes with a fan blade & fan motor, just use the fan blade out of the Belling box which is not as large & doesn’t run tight to element.

[Seamy]

Re: electrolux esl 6114 wont fill

Thats got an anti flood type solenoid on it so its more than likely shutting off due to air pressure sensed in the little hose, this activates the valve not to let in water.

Check fill matrix/iwms for blockage.

[Seamy]

Re: Beko Dishwasher DWD5411 – salt problems

Stir the salt in chamber after filling to dissolve saline solution. Theres a float in the tank that operates a reed switch which gives feedback on the salt level. Fine cable from this & from water counter breaks in loom below door sometimes/

[Seamy]

Re: Beko DCU8230

Sometimes short circuit on the NTC of heating element takes out P.C.B so that may need replacing. New heaters now have better design of NTC, its not needed to change P.C.B just for new style heater, but as previously stated original faulty NTC may have taken out board.

[Seamy]

Re: Belling Bi60f headache

TOC mounted at back of oven sometimes blows also when lamp shorts as described.

[Seamy]

Re: Zanussi ZWHB7160 cannot open filter in drum

Hi Bernie, some of these don’t have filter that customer can empty & instead need a torx driver to open.
If you need to you can take pump off from underneath, theres a plastic inner part behind pump on some of them that can hold coins etc.

[Seamy]

Re: Tumble dryer stopped working

P.C.B & heater required most likely, either or or worse case scenario both. Best to have an engineer look at it perhaps.

[Seamy]

Re: Zanussi ZWG1120M – Shuts off powers off after less than

Try a multimeter/test meter, check heater & motor in particular foe low resistance to earth.
Presuming its not losing power because of supply problem, try plugging into different socket.

[Seamy]

Re: Beko DW450 PCB replacement

PCB should do the trick.

[Author]

Posts